WEBER CALIBRATED

                 PARTS

                                             TO ORDER OR FOR MORE INFO CALL (205) 823-7278   

Weber carburetors are somewhat unique in that adjustments are not made by turning screws and then guessing how far in or out you are. With Webers, adjustments are made by replacing a calibrated part with a calibrated part of a different size. The size of the part is always stamped on it so that you know exactly where you are. This allows for very precise tuning for maximum HP. To order, call (205) 823-7278.

                                                                           MAIN JETS:

WEBER MAIN JETS FOR DCO, DCOE, DCNI, IDF, 48IDA ---------- BASIC  PART #73401 ------ $8.00 EACH SIZES AVAILABLE (IN MM): 090, 095, 100, 105, 110, 115, 120, 125, 130, 135, 140, 145, 150, 155, 160, 170, 180, 190, 200, 210, 200, 230

WEBER MAIN JETS FOR DCNF, DATRA, DFTA, DMTRA, DMTR ---BASIC PART #73405 ------ $8.00 EACH SIZES AVAILABLE (IN MM): 100, 105, 110, 115, 120, 125, 130, 135, 140, 145, 150, 155, 160, 165, 170, 180, 190, 200

WEBER MAIN JETS FOR ADFA, DARA, DCD, DIR, DFM, DGV, DMSA, DCN, DCZ, DIC, DICA, DHSA, DFI, DGAV, & 3-BBL CARBS ---------------------------------------------------BASIC PART #73801 ----- $8.00 EACH SIZES AVAILABLE (IN MM): 090, 095, 100, 105, 110, 115, 120, 125, 130, 135, 140, 145, 150, 155, 160, 165, 170, 180, 190, 200, 210, 220

                                                  AIR CORRECTOR JETS:

WEBER AIR CORRECTOR JETS FOR ADFA, DHSA, DFM, DGV, DGAV, DFAV, DMSA, DCN, DIR, DIC, DICA, DFI, & 3-BBL CARBS ----------------------------------------------BASIC PART #77201 ----- $8.00 EACH SIZES AVAILABLE (IN MM): 100, 105, 100, 115, 120, 125, 130, 135, 140, 145, 150, 155, 160, 165, 170, 180, 190, 200, 210, 220, 230, 240

WEBER AIR CORRECTOR JETS FOR DCO, DCNL, DCOE, IDA, IDF - BASIC PART #77401 -- $8.00 EACH SIZES AVAILABLE (IN MM): 100, 105, 110, 115, 120, 125, 130, 135, 140, 145, 150, 155, 160, 170, 180, 190, 200, 210, 220, 230, 230

WEBER AIR CORRECTOR JETS FOR  DCNF, DMTR, DMTRA, DATRA, DFTA, DHTA #77501 -- $8.00 EACH SIZES AVAILABLE (IN MM): 100, 105, 110, 115, 120, 125, 130, 135, 140, 145, 150, 155, 160, 170, 180, 190, 200, 210, 220

                                        CHOKE TUBES (VENTURIS) ALL TYPES ---- $36.00:

WEBER CARB TYPE BASIC PART NUMBER   SIZES AVAILABLE
  28/36 DCD (PRI) 71702 24,26
28/36 DCD (SEC) & 36 DCD 71701 24, 26, 28
40DCN, DCNF 72129 24, 26, 28, 30, 32, 34, 36
40DCOE 72303 26, 28, 30, 32, 34, 36
40IDA 3-BBL, 40 IDT 3-BBL, 40IDPT 3-BBL    71502 30, 32, 34
40IDF 13, 15, 19 71506 32
42DCNF 72106 32, 34, 36
44IDF  71507              32,36
45DCOE  72110 30, 32, 34, 36, 38, 40
48DCOE  72117                  40, 42 
48IDA  72128 36, 38, 40, 42, 44
48IDF  71513 40

    

 DCOE AUXILIARY VENTURIS (SECONDARY VENTURIS) ALL TYPES ----- $36.00:

WEBER CARB TYPE                   BASIC PART NUMBER                            SIZES AVAILABLE
40DCOE                                                   70001                   3.50, 4.50 (NO RAM PIPES)
40DCOE                      70003               3.50, 4.50 (WITH RAM PIPES)
42DCOE                  70002               3.50, 4.50 (WITH RAM PIPES)
45DCOE                  69602                       3.50, 4.50 (WITH RAM PIPES)
45DCOE                  69904                    4.50 (NO RAM PIPES)   
48DCOE                  68819                        4.50, 5.00 (WITH RAM PIPES)

 

          AUXILIARY VENTURIS FOR DOWNDRAFT CARBS --- ALL TYPES ----- $36.00:

WEBER CARB TYPE                       BASIC PART NUMBER          SIZES AVAILABLE
32/36DGV, DGAV, DGEV                                 71111                                3.50
40DCNF                                                               71107                                     3.50, 4.50 
40IDF 13, 15                                                           69002                                    4.00, 5.00
40IDF 19                                                                 69011                                   3.00, 4.50 
 44IDF                                                                    71102                              3.50, 4.00, 4.50 
 48IDA                                                                    69009                             3.50, 4.00, 4.50
 48IDF                                                                      71124                             3.50, 4.00, 4.50

 

                             IDLE JETS FOR DCOE CARBURETORS --- $12.00 EACH:

    Please note that there is no correlation between the size of the "F" number and the size of the air bleed hole in DCOE idle jets. Weber (in it's infinite wisdom) simply assigned F numbers at random to the various air bleed hole sizes. In choosing an idle jet bleed hole size please go by the following scale.

                    RICHER     F6 -- F12 -- F9 -- F8 -- F11 -- F13 -- F2 -- F4 -- F5 -- F7 -- F1 -- F3    LEANER

    The fuel hole size is given in mm, so a F1-.50 idle jet would have two 1.40mm air bleed holes (quite lean) and a .50mm diameter fuel hole. Utterly confused? Call us for help at (205) 823-7278.

BASIC PART #   "F' NUMBER AIR HOLE SIZE  FUEL HOLE SIZES AVAILABLE
74814 F1 2 X 1.40                                  .40, .50, .55
74815 F2 1 X 1.40                         .40, .45. .50, .55, .60
74816           F3           2 X 1.60                      .40, .45, .50, .55, .60
74817            F4             1 X 1.40                                     .40, .45, .60
74818            F5              1 X 1.60                          .40, .50, .55, .60, .65
 74819          F6                  1 X .70                           .40, .45, .50, .55, .60, .65
 74820          F7 2 X 1.20                   .40, .45, .50, .55
 74821        F8 1 X 1.20                        .40, .45, .50, .55, .60, .65
74822           F9 1 X 1.00          .40, .45, .50, .55, .60, .65
74824           F11 1 X 1.20       .40, .45, .50, .55, .60, .65
74825           F12 1 X .90               .40, .45, .50, .55
74826           F13 2 X .90                     .40, .50, .55
74827          F14 1 X 1.20                            .50
 74828          F15 1 X 1.05                            .50

 

              IDLE JETS FOR DOWNDRAFT WEBER CARBURETORS ----- $12.00 EACH:

TYPE OF CARBURETOR                                         SIZES AVAILABLE
DGV, DFD, DFAV, DGAV, DMSA, DGAS, DIC         .40, .42, .45, .47, .50, .52, .57, .60,.65,.70
DCD, DLED, DCN                                                      .40, .45, .50, .55, .60, .65, .70
DCNF & IDF                     .40, .45, .47, .50, .52, .55, .57, .60, .65, .70
ADFA & DGV WITH IDLE SOLENOID                                     .45, .47, .50, .

  

         EMULSION TUBES FOR DCOE, IDA, IDF, DCNL ---- BASIC PART #61450---- $36.00 EACH

PART NUMBER F NUMBER PART NUMBER F NUMBER PART NUMBER F NUMBER
61450.026                 F1      61450.027           F2 61450.028          F3
61450.051                 F4          61450.029           F5 61450.071          F6
61450.091                 F7     61450.092           F8   61450.030          F9
61450.031                 F11   61450.131           F12   61450.166          F14
61450.032                  F15   61450.181           F16 61450.052          F17
61450.053                   F20     61450.054           F34    

 

  EMULSION TUBES FOR WEBER DOWNDRAFT & 3BBL ---- BASIC PART #61440 ---- $36.00 EACH

PART NUMBER  F NUMBER PART NUMBER  F NUMBER PART NUMBER F NUMBER
61440.150               F1 61440.166          F2 61440.181            F3
61440.182                 F5 61440.211          F6 61440.226            F7
61440.213                 F24 61440.488          F25 61440.151            F26
61440.502                 F33 61440.352          F38 61440.216            F50
61440.217                 F53 61440.220          F66          

                             

                                ACCELERATOR PUMP JETS ------ $16.00 EACH

WEBER CARB TYPE  BASIC PART NUMBER                             SIZES AVAILABLE
IDF SERIES 76210                                      .40, .50, .55
DGV, DGAV, DGEV 76226                                         .50
DCOE SERIES                             76801                  .35, .40, .45, .50, .60, .70, .90
DFAV, DFI, DGAS    76212                   .40, .45, .50, .55, .60 
DCN, DCNF SERIES 76215                        .40, .45, .50, .55, .60, .65, .70

        

        ACCELERATOR PUMP INLET AND EXHAUST VALVES ------ $16.00 EACH                ============================================================================ FOR WEBER CARBS 28/36DCD, 36 DCD, DCOE, IDA, IDF, ICT -------------------- BASIC PART NUMBER 79701 AVAILABLE SIZES: CLOSED, .35, .40, .45, .50, .55, .60, .65, .70, .75, .80, .85, .90, .95, 1.00

                                                                                                                                                   

                        NEEDLE VALVES -------------- $26.00 EACH

WEBER CARB TYPE BASIC PART NUMBER        SIZES AVAILABLE
DCOE (SOLID TYPE) 79401                                 1.50, 1.75, 2.00 
DCOE (SPRING LOADED TYPE) 79503                                     1.50, 1.75, 2.00        
DCO 79502                                      1.75                   
IDA 46 & 48 (2 BBL) 79504                                       1.75, 2.00, 2.50           
DHSA, DCD, DIC, DICA, DATRA, DMTR, DMTRA  79507 1.50, 1.75, 2.00
DCN & DCNF 79514                               1.50, 1.75, 2.00
40 DFAV 79515                                 2.00, 2.50 
32/36 DFAV, 32/36 DGV, 32/36 DGAV, DGEV 9516 1.75, 2.00, 2.50

SHIPPING & HANDLING:    BY GROUND, $12.00        BY 2-DAY AIR, $24.00        BY NEXT DAY AIR, $48.00

  Weber Dir.